counter for wordpress

EFHW Antenna EFHW-7510-2K+ 2000W 75-10m / NO TUNER NEEDED!! / 132 feet long

By |July 23rd, 2026|

EFHW-7510-2K-PLUS Multi-Band End Fed Half Wave Antenna- NO TUNER NEEDED!EFHW-7510-2K-Plus, 2000W Multi-Band End Fed Half Wave AntennaImproved version of the EFHW-7510-2K, now with three large cores, 2.9-inch diameter, featuring just 0.5 dB Insertion loss 3-30MHz!This is an End-Fed Half-Wave (EFHW*) antenna for 75/40/30/20/17/15/12 and 10m bands. Unlike many END FED antennas on the market, this one does not require the Antenna Tuner to operate. Due to the High Impedance feed point, the antenna is less height dependent. You can put it up at 10 or 50 feet in the air without much change in VSWR values.*This is perfect antenna for ALE HF-link stations, NVIS, MARS, ARES, EMCOMM etc.Various installations such as horizontal, vertical, inverted V, inverted L, etc. are possible. Your VSWR values could vary with different wire configurations and the height of installation.NO TUNER needed!NO counterpoise needed! (Grounding recommended*)Frequency coverage: 3.5-30MHzResonant on 75/40/30/20/17/15/12/10mWire length ~130 feetPower Handling: 2kW I.C.A.S350W digital modes continuous (FT8, RTTY, etc)Stainless Steel hardwareStealth #14 AWG XLPE black wireConnector: Silver/Teflon SO-239The 2K-Plus model has three large stacked cores *Grounding at the transformer box or end of the coaxial cable is recommended for protection of your equipment from an electrostatic buildup in order to prevent ESD- electrostatic discharge.NOTE: grounding does not affect antenna tuning. If the transformer box is installed high above the ground , there is no need to route the ground wire from the box, instead just ground the coaxial cable at the entrance to your home or at the station.---------------------------------------------------------------------------------------------No guarantee or liability is either expressed or implied pertaining to damages to persons, buildings, or equipment in the installation or use of our antennas. You must use extreme caution when working around power lines. If the antenna were to come into contact with a voltage carrying line it could be fatal.

ANTENNA MOXON HUB with 2 and 1.5 in U-bolts for the mast

By |July 23rd, 2026|

For Sale, Aluminum Hub for 2 el Moxon Antenna Project. Bands: 6m - 20m Here is spec: 0.25 thickness Aluminum 9.5 in x 6 in, with holes and yellow zinc plated u-bolts (1/4 x 20) with nuts to fit 1" tube.

Comet CF-416A HF-VHF/UHF Transceiver Duplexer – 1.3-170Mhz & 350-540Mhz

By |July 23rd, 2026|

Comet CF-416A Duplexer. 2 Input leads, 1.3-170Mhz, the other accepts 350-540Mhz. Use 2 seperate VHF & UHF radios on 1 DualBand antenna.

Comet CF-4160 duplexer

By |July 23rd, 2026|

Comet CF-4160 duplexer

USED WORKING Comet CF-416 Duplexer 1.3–170MHz / 350–540MHz TESTED CLEAN

By |July 23rd, 2026|

RF Industries UHF Duplexer

By |July 23rd, 2026|

RF industries UHF duplexer, will need to be retuned for your frequencies.

NEW Comet CF-142 Duplexer w/ Leads 1.3-150MHz & 200-480MHz

By |July 23rd, 2026|

AT-16-2 6-Way Coax Remote Antenna Switch KIT 1.8MHz-30MHz 800W PEP

By |July 22nd, 2026|

Power: 800W PEP. AT-16 6-Way Coax Remote Antenna Switch KIT SO-239 1.8MHz-30MHz. The TX center is not connected to the center of other antennas. The center of ANT1-6 is grounded when it is not powered, so you can only use one radio with 6 antennas, not the other way around.

6:1 DIY KIT 6-way coax remote antenna switch SO-239 HF MW Omron Ham Radio

By |July 22nd, 2026|

DIY Kit 6-way antenna switch This antenna switch has the highest isolation between the input and output of the antennas not used. The unused inputs are grounded to protect static electricity. Powerful OMRON G2RL 12v relays can be loaded up to 3kW PEP. Frequency range: 0.1 - 60 MHz The circuit board is designed to offer the best insulation and current carrying capacity. The dimensions of the board is approx 5.9x5.9 inch (150x150mm). Relays are controlled with positive polarity. The Kit is very easy to assemble. Kit contains:- 1pc double sided PCB antenna switch with solder mask for the HF (short wave) 6:1 antenna switch- 7pc SO-239 Connectors- 6pc 12v Relays OMRON G2RL - 6pc 1N4007- 6pc capacitors- 1pc 8 pin Terminal block with screw All components are brand new and not used. Shipping from Europe! Additional pictures of other works for your inspiration are here Schematic and bill of material can be downloaded from here Copy this link to your favourite browser =======>> radio-traffic.de/img/sh_6in1.png Drill plan can be downloaded from here Copy this link to your favourite browser =======>> radio-traffic.de/img/PCB-6in1.jpg Attention! Recently, several vendors with counterfeit my switches have appeared here. My design was developed in 2011, since then several hundred of them have been operating around the world, without complaints. Thank you for choosing my products.

SO-239 6-way 1.8MHz-60MHz 6:1 Coax Remote Antenna Switch Module KIT or Assembled

By |July 22nd, 2026|

6-way DIY Kit 6:1 Coax Remote Antenna Switch SO-239 1.8MHz--60MHz. Frequency: 1.8MHz--60MHz. The antenna switch has good isolation effect, and it adopts imported Austrian high-quality relays. 1 x Antenna Switch Kit.