The single-band 80m-10m end-feed half-wave linear antenna provides the antenna. It is designed as a highly portable wired antenna that can be easily set as an inverted V-shaped, horizontal, tilted, or vertical radiator (at higher frequencies).
Connector: PL259(UHF/U) type male for SO-239 socket. Frequency Range:DC- 1GHz(0-1.0GHz). 1 x Dummy Load. Impedance:50 Ohms. Shell Material:Aluminum alloy. Temperature Range: -55°C to +125°C.
The single-band 80m-10m end-feed half-wave linear antenna provides the antenna. It is designed as a highly portable wired antenna that can be easily set as an inverted V-shaped, horizontal, tilted, or vertical radiator (at higher frequencies).
This is a custom built dummy load. 50 ohm. 1000 Watts pep rating. Has fan for cooling. Included wire pigtail to connect to 12-14 volts dc power. This is NOT designed for continuous duty. Short am carrier transmits to tune amp etc. Let cool for short time between transmissions, etc. these are built per order. Handling time is set to 4 days. But should ship within 24-48 hours. Thanks for looking.
Impedance: 4 Ohms. Damped rear chamber for low Fs (345 Hz). Lightweight and rigid 2” woven carbon fiber diaphragm and rubber surround. Rigid cast aluminum faceplate. Low distortion with smooth response from 700 to 6,000 Hz.
Specification Frequency Range:DC- 3GHz(0-3.0GHz) Impedance:50 Ohm VSWR: ≤ 1.20 Connector: N type Shell Material:Aluminum alloy Temperature Range: -55°C to +125°C Dimension:length x diameter 5W: 45x30mm 10W: 55x30mm 25W: 70x30mm 30W: 95x45mm 50W: 95x45mm 100W:100x60mm Package content / lot : 1 x Dummy Load Shipping Item will be shipped to worldwide by air-mail to your eBay registered address. If you need to change your address. please make an annotation or leave us a message when you pay through PayPal. We usually ship the order within 1 business days( excluding Saturday and Sunday) .It takes about 11-23 business days for you to get the package. If you want express shipping ,please contact us. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility.
**BNC Female Jack Bulkhead Mount RF Connector - 50é â 1/2/5/10 Packs** Upgrade your radio setup with our BNC Female Jack Bulkhead Mount RF Connector. Designed for seamless installation in CB radios, HAM systems, and CCTV setups, this reliable connector features a rear solder cup terminal for a low-loss, permanent connection. **Key Features:** - **Panel-Mount Design:** Securely installs through your chassis with included mounting hardware. - **Durable Build:** Nickel-plated brass body for long-lasting performance. - **Optimal Signal Transfer:** Silver-plated contacts ensure low resistance. - **Versatile Packs:** Available in 1, 2, 5, or 10-piece options to suit your needs. **Specifications:** - **Impedance:** 50é - **Frequency Range:** DC â 4 GHz - **Includes:** Mounting nut and lock washer.
One New 800 Watt Hybrid 50 ohm Load Resistor good to 500 MHz This auction is for one piece of hybrid 50 ohm terminating load resistors rated at 800 watts continuous power dissipation when installed on an appropriate heat sink. It is a solder in type part with no RF connectors, and 1500 watts PEP for short periods. They measures approximately 2 inch long x 1 inch wide x .25 inch high and are rated up to 500 MHz with a VSWR of less than 1.3. For pulse operation, the part is rated at 8000 watts for 1% duty cycle and pulses less than 100 microseconds. These parts are good to build your own load or for terminating isolator circuits on RF amplifiers. The parts are new and guaranteed good or your money back. This is inventory from Henry Radio in Los Angeles, California. Shipping anywhere in the continental US is FREE. Pay me securely with any major credit card through PayPal!