counter for wordpress

HF End Fed Dipole UJM-EFHW-80-10 200W 80-10m / NO TUNER NEEDED!! / 130 ft long

By |July 22nd, 2026|

eBay's Top Portable Antenna Seller NO TUNER NEEDED THIS IS THE UJM-EFHW-80-10 This antenna is made by using a matching network consisting of a 49:1 bifilar wound toroid with the needed capacitance added for wide, multi band, no tuner needed operation. PLEASE LOOK AT ALL PICTURES TO SEE THE DETAILS AND CRAFTSMANSHIP! This sale is for a true, half wave end fed antenna for 80-10 meters This antenna is rated at 200W PEP and 75W digital/CW@50/50 duty and is PERFECT for both portable or permanent installations! This antenna comes complete with 130 feet of stealthy but strong MARINE 18AWG fully tinned insulated copper stranded wire. Marine wire is tough and made for harsh environments. Nylon UV dogbone insulator and all Stainless Steel hardware on the matching box. The box is sealed with a foam gasket as well. Without a tuner the antenna works 80,40,20,15, 10 and usually 12 meters as well. 12 meters will depend on your setup. With a decent tuner you can also tune 30 and 12 meters and 17 meters. I do also have a 40 thru 10 meter version listed for sale and is only 65 feet long. One of the great things about this antenna is that the height you mount it will have a smaller affect on SWR than other antenna types. This gives you a large flexibility in your installation. One huge advantage of these antennas is that they typically have very good "ears" with a low noise floor! Please note, I used the same pictures for this listing as my 40-10 meter version so the 80m SWR is not shown but just as good as others. As you can see from the picture the antenna box does come with the mounting eye-bolt wired for optional ground however with this type of antenna adding a ground or counterpoise will have little to no affect on the antenna tuning and is not needed since it's built as a DC ground potential antenna already. Also, NO RF CHOKE NEEDED IN MOST INSTALLATIONS! Antenna uses a standard SO-239 connector to accept your coax with PL-259 connectors. Most users will find no rf issues and find no rf choke is needed. That said, using a GOOD rf choke is always good ham practice and I do have my own designed choke/s with full choking specifications listed with the one authorized distributor for them. It can be found by putting the eBay item number in the eBay search bar. That number is 264946030545 Another advantage of this antenna is the endless ways you can deploy it. I recommend a simple sloper installation and you can mount the box close to the ground with your element sloping upwards. When installed as a sloper you will see fantastic results if you can get the far end of the element up to 25' or more. That being said, you can install this antenna: horizontal, vertical, inverted "L", zigzag and more. The screenshot pictures shown above on the Rigol Spectrum Analyzer and SWR at the radio are shown with the antenna in a sloper configuration with the box fed at 5 feet and the far end up at 27' from the ground fed with 75' of LMR400 coax. Your unique installation may vary those reading a bit. This is a very simple antenna to install and no extra instructions are necessary but if you do have any questions please feel free to ask. Simply secure a cord to the mounting eye-bolt and stretch out your element for your installation and secure it. Great for ALE HF-link stations, NVIS, MARS, ARES, EMCOMM I have produced and sold more than 15,000 antennas here on eBay alone and still maintain a 100% positive feedback for a reason. everything I make and send is made by myself, no help allowed and only made as if it were as my own antenna. I feed my family this way and so my customers ALWAYS get the highest level of quality and customer service I can provide. To put it simple, my livelihood depends on it. If anyone has an issue at all, please just send me a message through eBay and I will take care of you as I have done on here for over 7 years now. I also have 9:1 unun Random Wire Matchboxes that are designed to be used with a tuner on all bands with a *random* length wire as well. PLEASE LOOK AT MY OTHER LISTINGS! 73 KD8UJM

Replacement 80-10m element section for the UJM-EFHW-80-10 1kW (Not 200W) antenna

By |July 22nd, 2026|

Replacement wire for UJM-80-10-1kW+ antenna. Includes coil, clamp and insulator and soldered connector as shown. Does not include the clamp for attaching the element to the box because you should already have that. Approx 130' long. This is the element only and not the complete antenna. This listing is meant as a replacement for the UJM-EFHW-80-10-1kW+ antenna. This is not the element for the 200W antenna version. If you own the UJM-EFHW-40-10-1kW+ antenna, this tuned element is a direct swap for your 40-10m unit to gain 80 meters as well. Length of this element is approximately 130 feet long. This tuned element is made with the same material used in my complete antenna. MARINE fully tinned16AWG insulated stranded copper element wire with stainless hardware and UV insulator. Marine wire is tough and made for harsh environments

25 Feet #8 AWG Aluminum Grounding wire

By |July 22nd, 2026|

(RADIO SHACK) AUTOMATIC ANTENNA MAST AUTO-ROTATOR SYSTEM -WORKS GREAT VERY NICE!

By |July 22nd, 2026|

The Radio Shack Antenna Mast Automatic Rotator was a must have unit for any HAM/CB operator/ enthusiast, which features motorized rotation and multi-directional capabilities.

EFHW-7510-LP

By |July 22nd, 2026|

EFHW-7510-LP EFHW-7510-LP- 250W Portable or Stationary Multi-Band End Fed Half Wave Antenna/ This is a 250W version of the popular EFHW-7510-2K+ End-Fed Half-Wave (EFHW*) antenna for 80/40/30/20/17/15/12 and 10m bands. Featuring an optimized MEF-130-LP transformer with an average insertion loss of only -0.4 dB (~9% loss) compared to similar products on market with insertion loss as high as -1.5dB (~30% loss). Unlike many END FED antennas on the market, this one does not require the Antenna Tuner to operate. Check the 75M band coverage SWR chart below. *This is perfect antenna for ALE HF-link stations, NVIS, MARS, ARES, EMCOMM etc. Various installations such as horizontal, vertical, inverted V, inverted L, etc. are possible. Measured VSWR in the gallery are taken with the antenna horizontal at 25 feet above the ground, your values could vary with the way and height of installation. NO TUNER is needed! NO counterpoise is needed! Frequency coverage: 3.5-30MHz Resonant on 80/40/30/20/17/15/12 and 10M Wire length ~130 feet Power Handling: 250W I.C.A.S Digital Modes, FT8 100W max. Stainless Steel hardware Stealth #16 AWG black wire Connector: Silver/Teflon SO-239 *Grounding of the coaxial cable at the radio side is recommended for the protection of your equipment from an electrostatic buildup in order to prevent ESD- electrostatic discharge. NOTE: grounding does not affect antenna tuning. *Amateur Radio Emergency Service® (ARES), ALE-Automatic Link Establishment (HFlink), MARS-The U.S. Army Military Auxiliary Radio System (AMARS), NVIS EFHW-7510-LP EFHW-7510-LP- 250W Portable or Stationary Multi-Band End Fed Half Wave Antenna/ This is a 250W version of the popular EFHW-7510-2K+ End-Fed Half-Wave (EFHW*) antenna for 80/40/30/20/17/15/12 and 10m bands. Featuring an optimized MEF-130-LP transformer with an average insertion loss of only -0.4 dB (~9% loss) compared to similar products on market with insertion loss as high as -1.5dB (~30% loss). Unlike many END FED antennas on the market, this one does not require the Antenna Tuner to operate. Check the 75M band coverage SWR chart below. *This is perfect antenna for ALE HF-link stations, NVIS, MARS, ARES, EMCOMM etc. Various installations such as horizontal, vertical, inverted V, inverted L, etc. are possible. Measured VSWR in the gallery are taken with the antenna horizontal at 25 feet above the ground, your values could vary with the way and height of installation. NO TUNER is needed! NO counterpoise is needed! Frequency coverage: 3.5-30MHz Resonant on 80/40/30/20/17/15/12 and 10M Wire length ~130 feet Power Handling: 250W I.C.A.S Digital Modes, FT8 100W max. Stainless Steel hardware Stealth #16 AWG black wire Connector: Silver/Teflon SO-239 *Grounding of the coaxial cable at the radio side is recommended for the protection of your equipment from an electrostatic buildup in order to prevent ESD- electrostatic discharge. NOTE: grounding does not affect antenna tuning. *Amateur Radio Emergency Service® (ARES), ALE-Automatic Link Establishment (HFlink), MARS-The U.S. Army Military Auxiliary Radio System (AMARS), NVIS &times &times &times &times &times &times &times &times &times &times &times &times &times &times Tell a friend Visit store Watch now Postage info Click the Postage tab above the listing description for more info Price: $9.99 (local shipping) See more... USPS Priority Mail - $9.99 USPS Priority Mail International - $45.00 Click the Postage tab above the listing description for more info! Additional delivery notes PICK UP OPTION Sorry, our items are NOT available for pick-up. PAYING VIA PAYPAL We accept PayPal on our all our items so you can shop with confidence. Simple choose the PayPal option when proceeding through the checkout. Additional Information No additional information at this time Ask seller a question You might also like Antenna End Insulator-10 RFI-Kit-2 EFHW-60S-1K SWL antenna Contact To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist. Ask seller a question © Antennas and accessories designed by Danny Horvat, E73M Postage Shipping is a flat rate across US at a rate of $9.99 Payment Accepted Payment Methods PayPal Returns Returns are not accepted Buyer will pay for return shipping. eBay integration by

AMERITE ~ AME 25 – ACCESSORY SHELF-ROTOR PLATE, OEM, GENUINE

By |July 22nd, 2026|

****NEW**** AME 25 ACCESSORY SHELF ROTOR PLATE- - Genuine OEM - - GALVANIZED STEELHeavy Duty IDEAL FOR MOUNTING OF ROTOR'S, EQUIPMENT, CONTROLS, ETC. PRE-DRILLED FOR MOST ROTOR SIZES AND MODELS GREAT FOR HAM, WI-FI OR RADIO TOWER APPLICATIONS INCLUDES MOUNTING HARDWARE - U BOLTS..... NOTHING ELSE TO BUY!! AMERICAN/AMERITE TOWER -AMERICAN TOWER/AMERITE AME20 & AME25-Fits Rohn 25G Tower as well. GREAT FOR INSTALLING ANTENNA ROTORS TO PICK UP HIGH DEF TELEVISION!!!! FINISH: GALVANIZED STEEL NOT A HOME MADE SPRAY PAINTED PRODUCT. FITS TOWER WITH ORIGINAL 'ZIG-ZAG' DESIGN AND CONSTRUCTION AS WELL. ALL STEEL IS TO ASTM SPECIFICATIONS AND IS MILL CERTIFIED. PLEASE NOTE THAT THIS IS MADE BY AN O.E.M TOWER MANUFACTURER, AMERICAN TOWER COMPANY, WHO HAS BEEN BUILDING TOWER SINCE 1953. USA OWNED & MADE. MEETS ALL TOWER SPEC'S AND CONSTRUCTION METHODS. WILL SHIP TO ALL 48 STATES. UPS GROUND. NO P.O. BOXES. FLAT RATE SHIPPING. PAYMENT IN 3 DAYS FOR PAY PAL SERIOUS TOWER FOLKS WILL LOVE THIS PRODUCT!!!! CHECK OUR STORE FOR OTHER TOWER PRODUCTS!!! Made in the USA by a USA Company, by a USA Dealer. 100% American. Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.

AN/PRC-112G (ANTENNA)

By |July 22nd, 2026|

Polypropylene-Hydraulic-Clamps OD 3/4″ (Lot of 10 pairs)

By |July 22nd, 2026|

For sale Lot of 10 pairs Polypropylene Pipe/Tubes Saddle Clamps. This is the best clamps for mounting antennas and element tubing. This is especially helpful when you need insulated Yagi element or GP/Vertical Antenna. Clamps are useful for securely mounting tubing to any flat surface, while providing electrical insulation. Standard: DIN 3015 UV Resistant For tube Size OD: 3/4” ( 0.75") – 19mm If you need other quantity please contact me. from 7/15/21. 2" is available...

Polypropylene Pipe/Tubes Clamps Green Insulators OD 7/8″ (Lot of 10 pairs)

By |July 22nd, 2026|

2" is available.

Polypropylene-Hydraulic-Clamps OD 1-3/8″ (35mm) (Lot of 10 pairs)

By |July 22nd, 2026|

For sale Lot of 10 pairs Polypropylene Pipe/Tubes Saddle Clamps. This is the best clamps for mounting antennas and element tubing. This is especially helpful when you need insulated Yagi element or GP/Vertical Antenna. Clamps are useful for securely mounting tubing to any flat surface, while providing electrical insulation. Standard: DIN 3015 UV Resistant, For tube Size OD:1-3/8” or 35mm. If you need other quantity please contact me.